Back to Blog
Comparisons 2026-11-16 Kunkune 1 views

Nokia 5110 LCD vs 1.8 inch TFT: Arduino Display Choice

Nokia 5110 LCD vs 1.8 inch TFT: Arduino Display Choice

Compare the Nokia 5110 LCD and 1.8 inch TFT for Arduino: logic voltage, wiring, libraries, and which small display suits your project.

Two small displays, two different design briefs

The Nokia 5110 LCD and the 1.8 inch TFT are both inexpensive Arduino displays, but they solve different problems. The Nokia 5110 gives you an 84×48 monochrome screen with a blue backlight, while the 1.8 inch TFT gives you a 128×160 colour screen. That difference in pixels and colour shapes everything else: how much you can show, how you wire it, and how much code you need to get a readable result.

This comparison sticks to what the supplied product records confirm. Where a detail is not in those records, treat it as an open question to check against your own board and library rather than as a missing feature.

Screen, interface, and logic voltage at a glance

  • Display type and resolution: Nokia 5110: 84×48 monochrome LCD with blue backlight. 1.8 inch TFT: 128×160 colour, 65K colours (16-bit RGB565). The TFT shows more information and colour; the Nokia is text-first.
  • Controller and interface: Nokia 5110 uses the PCD8544 controller over a 5-wire SPI interface (CLK, DIN, DC, CE, RST). The 1.8 inch TFT uses the ST7735S controller over 4-wire SPI (MOSI, SCK, CS, DC, optional RST). Both are SPI displays, so pin count is similar.
  • Logic voltage: Both modules are 3.3V logic devices. The Nokia 5110 record says it connects directly to ESP8266 or ESP32 without level shifting, and needs 10k resistors on each SPI line for a 5V Arduino Uno. The TFT record says it connects natively to ESP32 and ESP8266, and needs a 4-channel bidirectional level shifter on MOSI, SCK, CS, and DC for a 5V Uno.
  • Backlight control: Both have a backlight pin (BL) that is PWM-dimmable for power saving. The Nokia 5110 record specifically notes the blue LED backlight is PWM dimmable.

Wiring a Nokia 5110 screen to Arduino: what changes with 5V

The Nokia 5110 screen wiring for Arduino follows the 5-wire SPI pinout: CLK, DIN, DC, CE, and RST. On a 3.3V board such as an ESP8266 or ESP32, the supplied record says it connects directly without level shifting. On a 5V Arduino Uno, the record calls for 10k resistors on each SPI line to protect the controller. That is a different approach from a dedicated level-shifter board, so plan your breadboard space accordingly.

The record does not supply a step-by-step wiring diagram or a pin-mapping table beyond the signal names. Use the signal labels on your specific module and your board's SPI pins, and verify the logic levels before powering up.

Nokia 5110 evidence that affects the wiring decision

Wiring the 1.8 inch TFT LCD 128×160 to Arduino: level shifting is not optional

The 1.8 inch TFT LCD 128×160 for Arduino uses 4-wire SPI: MOSI, SCK, CS, DC, and an optional RST. The ST7735S controller accepts 3.3V logic only, and the supplied record is explicit that the SD card SPI lines also require 3.3V. For a 5V Arduino Uno, the record specifies a 4-channel bidirectional level shifter on MOSI, SCK, CS, and DC. That is a firmer requirement than the resistor approach used on the Nokia 5110, so budget for a level-shifter module if you are staying with a 5V board.

The module also includes a micro SD card socket on the back that shares the SPI bus with a dedicated CS line. If you use the SD card, remember that those lines are also 3.3V logic. The record does not supply a full pinout diagram or a wiring sequence, so confirm the labels on your board before connecting.

1.8 inch TFT evidence that shapes the build

  • 1.8 inch TFT LCD Module 128×160 For Arduino: The ST7735S accepts 3.3V logic only. The SD card SPI lines also require 3.3V. This is the compatibility boundary: a 5V Uno needs level shifting on the SPI lines, and the SD card shares that constraint.
    1.8 inch TFT LCD Module 128×160 For Arduino
    1.8 inch TFT LCD Module 128×160 For Arduino
  • 1.8 inch TFT LCD Module 128×160 For Arduino: It runs on 3.3V logic and connects natively to ESP32 and ESP8266 boards; a simple level shifter on the SPI lines makes it compatible with 5V Arduino Uno boards. Board choice changes the wiring: 3.3V boards are direct, 5V boards need the shifter.
  • 1.8 inch TFT LCD Module 128×160 For Arduino: 4-wire SPI interface — MOSI, SCK, CS, DC, optional RST; micro SD card slot — shared SPI bus, separate CS line. Four control lines plus optional reset and a separate SD chip select define the pin budget.

Libraries and initialisation: different starting points

The Nokia 5110 record names the Adafruit PCD8544 library as compatible, which gives you a straightforward text and graphics starting point. The 1.8 inch TFT record names two options: the Adafruit ST7735 library for Arduino and ESP32, and Bodmer's TFT_eSPI library, which the record says is faster on ESP32 and uses SPI DMA for smooth animation at up to 40MHz. Both are in the Arduino Library Manager.

For the TFT, the record also notes that you should select the INITR_BLACKTAB or INITR_GREENTAB initialiser to match your specific module revision. That is a detail worth checking early: the wrong initialiser can produce a shifted or wrongly coloured image even when the wiring is correct. The Nokia 5110 record does not mention a comparable initialiser choice.

Which display fits your project

  • Choose the Nokia 5110 if: You need a cheap Arduino display module for text, sensor readouts, or a retro handheld look, and you are working with an ESP8266/ESP32 or are comfortable adding 10k resistors on a 5V Uno. The 84×48 monochrome screen and Adafruit PCD8544 library keep the software simple.
  • Choose the 1.8 inch TFT if: You need colour, more pixels for dashboards or graphics, and you can provide 3.3V logic directly or add a 4-channel level shifter for a 5V Uno. The 128×160 screen and ST7735S controller give you 65K colours, and the micro SD slot adds storage on the same SPI bus.
  • Check before you buy either: Confirm your board's logic voltage and whether you already own a level shifter or the required resistors. Neither record supplies a full wiring diagram or a complete setup sequence, so plan to verify pin labels and library initialisers against your own hardware.

Related Articles

Customer Service
Home
Products
Cart
Profile